| Home

3M 5200 Marine Adhesive Sealant| Subrosa Buy Online | SUBROSA Corporation Malaysia

Glue it! Bond it! Seal it with Subrosa Buy Online, Bonding & Sealing Solutions

Now 3M 5200 Sealant is available In-stock

in Subrosa Corporation Malaysia.

3M 5200 Marine Adhesive Sealant is a one-part polyurethane that chemically reacts with moisture to

deliver strong, flexible bonds. It has excellent adhesion to wood, gel coat and fiberglass. It forms a

watertight, weather-resistant seal on joints and boat hardware, above and below the waterline. In

addition, its flexibility allows for dissipation of stress caused by shock, vibration, swelling or shrinking.

Almost no environment is harsher than the beating sun and pounding waves of the open water.

3M’s full line of marine adhesives and sealants are time-tested to withstand all the hardships nature gives out.

Whether your application is above the water or below, 3M’s sure to have the right product for the job.

Ex-stock 3M 5200 Black or White 295ml Cartridge Sealant in Subrosa Corporation Malaysia.

Marine Adhesive Sealant

3M 5200 Marine Adhesive Sealant is a one-part polyurethane that chemically reacts with moisture to

deliver strong, flexible bonds. It has excellent adhesion to wood, gel coat and fiberglass.

Tough/flexible polyurethane polymer

3M 5200, Black or White

Fast Cure

3M 5200, high-performance polyurethane adhesive sealant becomes tack-free in 24-48 hours, and completely cures in 5-7 days with no shrinking.

The seal is extremely strong, retaining its strength above or below the waterline.

3M 5200 stays flexible–allows for structural movement. Stress caused by shock, vibration, swelling or shrinking is effectively absorbed. Has excellent resistance to weathering and salt water.

3M 5200 bonding & Sealing Solutions,

in the water or out.

Check the bonding and sealing

jobs this product can handle for you:

Applications:

Typical bonding and sealing applications include:

- Fiberglass deck to fiberglass hull

- Wood to fiberglass

- Porthole frames

- Deck fittings

- Moldings

- Trunk joints

- Between struts and planking

- Stern joints and hull planking

Structural bonding and sealing of:

- Wood

- Fiberglass

- Gel coat

- Primed metal

Sealing of:

- Some plastics (test before assembly)

- Glass

- Metals

Application Information :

Surface Preparation:

There are waxes, coatings, sealants, grease, oil and other

contaminants used in the marine industry,

making it very important to clean all surfaces to be bonded

before applying 3M Marine Adhesive Sealant 5200.

Recommended procedures include cleaning

with 3M General Purpose Adhesive

Cleaner*, P. N. 08984.

Application of Adhesive Sealant:

Abrading the surfaces with a 180 grit to 220 grit abrasive,

and subsequently wiping off residue, will enhance the bond strength.

Cut tip of the nozzle to desired bead size.

Puncture seal inside the threaded nozzle end and screw on nozzle.

If using a 10 fl. oz. cartridge, knock out the bottom seal

with a hammer and place the cartridge in a caulk gun.

Apply 3M Marine Adhesive Sealant 5200 to the seam or part to

be bonded. Position parts. Tool material to desired appearance.

Remove excess material with 3M

General Purpose Adhesive Cleaner*, P. N. 08984.

Cleanup:

For cleaning 3M Marine Adhesive Sealant 5200 before it is cured,

use a dry cloth to remove the majority of sealant,

followed by a cloth damp with General Purpose Adhesive

Cleaner*, P. N. 08984, toluene or acetone.

Cured 5200 can be removed mechanically with a knife, razor blade, or sanding.

Limitations -

- Alcohol should not be used in preparation for bonding

as it will stop the curing process,

causing the adhesive to fail..

- Heat resistance, due to the decreased value in bond strength

at elevated temperatures,

we do not recommend use of this product above 190°F (88°C).

- Do not apply at temperatures below 40°F (4°C) or on frost covered surfaces.

Do not apply at surface temperatures above 100°F (38°C).

- 3M Marine Adhesive Sealant 5200 is not recommended

for use as a teak deck seam sealer.

Extended exposure to chemicals (teak cleaners, oxalic acid, gasoline,

strong solvents and other harsh

chemicals) may cause permanent softening of the sealant.

- 3M Marine Adhesive Sealant 5200 is not recommended for the installation of glass,

polycarbonate or acrylic windows that are not also

mechanically fastened with a system designed by the manufacturer.

Inconsistent adhesion of these unprimed substrates, specific design of the window,

and movement due to thermal expansion and flexing,

may cause application failure. It is strongly recommended that the

customer contact the window/port light/hatch manufacturer for

recommendations on proper sealing procedures.

- When using 3M Marine Adhesive Sealant 5200 with metals,

it may be necessary to prime the surface to achieve adequate adhesion

and durability of the bond. Scotch-Weld Structural Adhesive Primer EC-

1945 B/A may be used for priming of most metals.

In Summary

Model: 3M 5200

Below Water Line (yes/no): Yes

Strength: Good

Material: Polyurethane Polymer

Type: Sealant

Usage: Bonding

Rate Of Cure: 5 days

Subrosa Marketing & Services

No.5-2-11, Jalan 3/109F,

Danau Business Center,

Taman Danau Desa,

58100 Kuala Lumpur, W. Persekutuan

Malaysia

Tel: +603 7987 8239 Fax: +603 7987 8239

E-mail: enquiry[@]subrosa.com.my

If you have any questions, feel free to ask.

Order Now @

SUBROSA BUY ONLINE

Example: Order Information

Description: 3M 5200

Size:
295ml Cartridge

Color: White

Application: bonding and sealing

Qty: 12 cartridge

Note: Stock items are subject to prior sales.

Home | Disclaimer